Washington Cycle Works

 
Go Back   Sportbike Addicts | Two Wheels... Our Drug of Choice > General > General Bike Talk
FAQ Members List Member Gallery Calendar Today's Posts Donate
Reply
 
Thread Tools Display Modes

Standing battery voltage loss
Old 06-08-2005, 12:49 PM   #1
jcblitz
Having Troubles w/His Wood
 
jcblitz's Avatar
 
jcblitz is offline
Join Date: May 2005
Location: Yesterday
Posts: 1,608
Default Standing battery voltage loss

I fully charged my battery yesterday and checked it, 12.3 or so. I ran my bike and it was holding around 14.3 for about 5 minutes. Turned the bike off and the battery was at 12.5. Checked it today with the bike off and it read about 11.5. Started the bike, checked it running, 14.3 again. Shut it off after 5 min, 12.5 again. Is it normal to loose that much voltage in a day or do you think something is draining it (even though the bike is off). I have an alarm and an LED hooked up and I have the ground wires running to the battery ground instead of a frame ground...anyone know if that matters? I don't think so, but just double checking.
  Reply With Quote

Old 06-08-2005, 01:41 PM   #2
Commuta_Busa
Slow Ass Busa
 
Commuta_Busa is offline
Join Date: Jun 2005
Location: Carteret, NJ
Posts: 246
Send a message via AIM to Commuta_Busa
Default

to answer your second question, it doesn't matter where you ground it as long as it's a good solid ground.

as for the voltage loss I would have to guess it's one of two things... your alarm is sucking down the battery or your battery is slowly loosing its charge. I would say it's more likely to be the alarm though. Batteries these days last pretty damn long esp sealed ones. Check what the amperage draw is while the bike is off this should be a good starting point.
__________________
thanks: Aeromotive/ACL/AIM sport/Tsukigi/AP racing/APE/BDE/Big CC racing/BMC/BoostbySmith/Brembo/Calico/Carbon Lorraine/Carpenter racing/Catalyst composites/Clear alternatives/Cometic/Cosworth/CP/Cycle-tek/Dynojet/Earl's plumbing/EK/FBG/Harris/Hel/Honda/Hyperpro/Innovate/Kickstand racing/Lee Shierts racing/Lindemann Engineering/Machine pro/Magnaflow/Mikuni/NLR/NOS/Pro-bolt/Penske/Puig/R&D/RCC turbos/RCS/RPM racing/SBS/Schnitz racing/Sharkskinz/Spencer cycles/Spiegler/Sprocket specialties/Stedman/The Motorhead/Thermo-Tec/Tiger racing/TTS/Walbro/Yamaha/Yoshimura R&D/World wide bearings/Zukinot
  Reply With Quote

Old 06-08-2005, 05:05 PM   #3
jcblitz
Having Troubles w/His Wood
 
jcblitz's Avatar
 
jcblitz is offline
Join Date: May 2005
Location: Yesterday
Posts: 1,608
Default

How do I check the amperage draw...and what am I checking the draw off...the alarm?
  Reply With Quote

Old 06-09-2005, 08:41 AM   #4
Commuta_Busa
Slow Ass Busa
 
Commuta_Busa is offline
Join Date: Jun 2005
Location: Carteret, NJ
Posts: 246
Send a message via AIM to Commuta_Busa
Default

do you have a multimeter?
__________________
thanks: Aeromotive/ACL/AIM sport/Tsukigi/AP racing/APE/BDE/Big CC racing/BMC/BoostbySmith/Brembo/Calico/Carbon Lorraine/Carpenter racing/Catalyst composites/Clear alternatives/Cometic/Cosworth/CP/Cycle-tek/Dynojet/Earl's plumbing/EK/FBG/Harris/Hel/Honda/Hyperpro/Innovate/Kickstand racing/Lee Shierts racing/Lindemann Engineering/Machine pro/Magnaflow/Mikuni/NLR/NOS/Pro-bolt/Penske/Puig/R&D/RCC turbos/RCS/RPM racing/SBS/Schnitz racing/Sharkskinz/Spencer cycles/Spiegler/Sprocket specialties/Stedman/The Motorhead/Thermo-Tec/Tiger racing/TTS/Walbro/Yamaha/Yoshimura R&D/World wide bearings/Zukinot
  Reply With Quote

Old 06-09-2005, 02:36 PM   #5
jcblitz
Having Troubles w/His Wood
 
jcblitz's Avatar
 
jcblitz is offline
Join Date: May 2005
Location: Yesterday
Posts: 1,608
Default

Yup, I've tried the 10ADC setting but I keep getting sparks and stuff and I don't have the manual for it.

It's http://www.sears.com/sr/javasr/produ...seBVCookie=Yes
  Reply With Quote

Old 06-09-2005, 03:39 PM   #6
Commuta_Busa
Slow Ass Busa
 
Commuta_Busa is offline
Join Date: Jun 2005
Location: Carteret, NJ
Posts: 246
Send a message via AIM to Commuta_Busa
Default

sparks! ahhhh put the multimeter down here's an easier way... disconnect the ground from the alarm system, charge up your batt, let it sit over night and then check the volts again... are you still getting a big drop or not as much now? if it's still a big drop then it's not your alarm sucking the juice.
__________________
thanks: Aeromotive/ACL/AIM sport/Tsukigi/AP racing/APE/BDE/Big CC racing/BMC/BoostbySmith/Brembo/Calico/Carbon Lorraine/Carpenter racing/Catalyst composites/Clear alternatives/Cometic/Cosworth/CP/Cycle-tek/Dynojet/Earl's plumbing/EK/FBG/Harris/Hel/Honda/Hyperpro/Innovate/Kickstand racing/Lee Shierts racing/Lindemann Engineering/Machine pro/Magnaflow/Mikuni/NLR/NOS/Pro-bolt/Penske/Puig/R&D/RCC turbos/RCS/RPM racing/SBS/Schnitz racing/Sharkskinz/Spencer cycles/Spiegler/Sprocket specialties/Stedman/The Motorhead/Thermo-Tec/Tiger racing/TTS/Walbro/Yamaha/Yoshimura R&D/World wide bearings/Zukinot
  Reply With Quote

Old 06-09-2005, 04:06 PM   #7
Cakes206
The Solution
 
Cakes206's Avatar
 
Cakes206 is offline
Join Date: May 2005
Location: New Joisey
Posts: 8,105
Send a message via AIM to Cakes206
Default

Quote:
Originally Posted by Commuta_Busa
sparks! ahhhh put the multimeter down here's an easier way... disconnect the ground from the alarm system, charge up your batt, let it sit over night and then check the volts again... are you still getting a big drop or not as much now? if it's still a big drop then it's not your alarm sucking the juice.

Is it possible that battery might have a weak/bad cell(s)?
__________________


Character is who you are when no one is looking.

The more you sweat in practice, the less you bleed in battle.
  Reply With Quote

Old 06-09-2005, 04:31 PM   #8
Commuta_Busa
Slow Ass Busa
 
Commuta_Busa is offline
Join Date: Jun 2005
Location: Carteret, NJ
Posts: 246
Send a message via AIM to Commuta_Busa
Default

it's possible that the battery is going bad... these days though they last a pretty long time... I would rule out the security system (which is aftermarket and could be installed improperly) first. The oposite way would be to take the battery out, let it sit over night and check it's volts... if they're down alot then the batt is history...
__________________
thanks: Aeromotive/ACL/AIM sport/Tsukigi/AP racing/APE/BDE/Big CC racing/BMC/BoostbySmith/Brembo/Calico/Carbon Lorraine/Carpenter racing/Catalyst composites/Clear alternatives/Cometic/Cosworth/CP/Cycle-tek/Dynojet/Earl's plumbing/EK/FBG/Harris/Hel/Honda/Hyperpro/Innovate/Kickstand racing/Lee Shierts racing/Lindemann Engineering/Machine pro/Magnaflow/Mikuni/NLR/NOS/Pro-bolt/Penske/Puig/R&D/RCC turbos/RCS/RPM racing/SBS/Schnitz racing/Sharkskinz/Spencer cycles/Spiegler/Sprocket specialties/Stedman/The Motorhead/Thermo-Tec/Tiger racing/TTS/Walbro/Yamaha/Yoshimura R&D/World wide bearings/Zukinot
  Reply With Quote

Old 06-09-2005, 06:11 PM   #9
Mack
Washes njf4i's Back With a Pink Loofa
 
Mack's Avatar
 
Mack is offline
Join Date: May 2005
Location: Pittsburgh, PA
Posts: 547
Send a message via AIM to Mack
Default

well first thing yes you're voltage will read high with the bike running like you said 14.3 because of the rectifier putting juice in....however will drop as soon as the bike is off to 11.9 to 12.3 volts thus being a 12 volt battery....my battery has been running between 11.5 and 11.8 when first turning on the bike and I have had no problems this year with it....although I think it's getting close to time to get a new battery...but you could always take it to like Auto Zone and they can check it to see if the cells are dead.....just my 2 cents
__________________
  Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -4. The time now is 11:19 AM.
 

vBulletin skin developed by: eXtremepixels
Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.