BurnCycle
09-06-2005, 08:41 PM
I recently picked up a Gear Position Indicator (GPI) for the TLS that simply uses 6 LED's. One of the nice features about this GPI is that it also incorporated a semi-active Timing Retard Eliminator (TRE) to circumvent the timing issues in 1st through 4th. Those timing issues also were the cause of low RPM stumbles on this bike but that's a different story.
I wanted to go with an OEM look to the install which meant looking at the gauge panel for placement. I figured the idiot light area would be a good place to start.
Start drilling...
http://www.mariposaderojo.com/Pics/TLS/GPI/LEDHoles.jpg
Slide them in (if it were just that easy)...
http://www.mariposaderojo.com/Pics/TLS/GPI/LEDInstalled.jpg
Open it up for the wires...
http://www.mariposaderojo.com/Pics/TLS/GPI/LEDPath1.jpg
Drill the screw hole out for the cable. I did this because it was the cables direct route in. Trying to get it though the access panel would have been a headache. I also flattened down some of the ridge that is there so the cable had more area to angle in.
http://www.mariposaderojo.com/Pics/TLS/GPI/LEDPath2.jpg
GPI box. From here I can turn the dial on the fly
http://www.mariposaderojo.com/Pics/TLS/GPI/GPIBox.jpg
On, but dialed in dim...
http://www.mariposaderojo.com/Pics/TLS/GPI/GPINlow.jpg
Full bright...
http://www.mariposaderojo.com/Pics/TLS/GPI/GPINhigh.jpg
What gear am I in?
1st, (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI1st.jpg) 2nd, (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI2nd.jpg) 3rd, (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI3rd.jpg) 4th, (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI4th.jpg) 5th, (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI5th.jpg) 6th. (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI6th.jpg)
And it always helps to have an extra set of hands around.
http://www.mariposaderojo.com/Pics/PK/TLPresley2.jpg
I wanted to go with an OEM look to the install which meant looking at the gauge panel for placement. I figured the idiot light area would be a good place to start.
Start drilling...
http://www.mariposaderojo.com/Pics/TLS/GPI/LEDHoles.jpg
Slide them in (if it were just that easy)...
http://www.mariposaderojo.com/Pics/TLS/GPI/LEDInstalled.jpg
Open it up for the wires...
http://www.mariposaderojo.com/Pics/TLS/GPI/LEDPath1.jpg
Drill the screw hole out for the cable. I did this because it was the cables direct route in. Trying to get it though the access panel would have been a headache. I also flattened down some of the ridge that is there so the cable had more area to angle in.
http://www.mariposaderojo.com/Pics/TLS/GPI/LEDPath2.jpg
GPI box. From here I can turn the dial on the fly
http://www.mariposaderojo.com/Pics/TLS/GPI/GPIBox.jpg
On, but dialed in dim...
http://www.mariposaderojo.com/Pics/TLS/GPI/GPINlow.jpg
Full bright...
http://www.mariposaderojo.com/Pics/TLS/GPI/GPINhigh.jpg
What gear am I in?
1st, (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI1st.jpg) 2nd, (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI2nd.jpg) 3rd, (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI3rd.jpg) 4th, (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI4th.jpg) 5th, (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI5th.jpg) 6th. (http://www.mariposaderojo.com/Pics/TLS/GPI/GPI6th.jpg)
And it always helps to have an extra set of hands around.
http://www.mariposaderojo.com/Pics/PK/TLPresley2.jpg