torq

[soda7o]

ok I KNOW I AM a pain.. but i finaly got some new no warped brake rotors fro my bike.. they shoud lbe comming by next week. i know they have to be torqued down .. anyone know the torqu specs.




or shoud li just take the tires off and bring them to wcw caus ei also want to get my tires balanced

thanks

[DougZ]

If it is the Gix, 16.5 ft/ lbs, blue loctite.

[soda7o]

If it is the Gix, 16.5 ft/ lbs, blue loctite.

yup 04 750
is thatfor front and back or front /back only

[DougZ]

It is for the front...that I know of..I am guessing back is same..I'll check manual tonight.

[soda7o]

It is for the front...that I know of..I am guessing back is same..I'll check manual tonight.


thanks dude.....
wher edi dyou get a maual from btw?

[DougZ]

SUZUKI :)

[soda7o]

doug Z whiel youare at it can yutlel me whatkind of bulbs is the 04 gix 750 using (h4 h7) and what is the part number of the dual filiment bulb that serves as hi and lo beam? thanks
you da man...

[Cakes206]

doug Z whiel youare at it can yutlel me whatkind of bulbs is the 04 gix 750 using (h4 h7) and what is the part number of the dual filiment bulb that serves as hi and lo beam? thanks
you da man...

http://www.ronayers.com/index.cfm

Fiche>Suzuki>GSX-R600>GSX-R600 2004 (K4)> Start Studyin ;)

[soda7o]

http://www.ronayers.com/index.cfm

Fiche>Suzuki>GSX-R600>GSX-R600 2004 (K4)> Start Studyin ;)


you are useless.. shit if i ante dto do thework myslef i woudl have done it.. but its eassier to just ask.. :0

[soda7o]

ONE MORE
I need to takeof fthe front tire what the size i need
someone anone please


JOW dont freaking send me to ron ayers cause they dont have sizes thanks you

[RonJ83]

whatever you need you should check out mrcycles.com they have every stock part for any bike.

[soda7o]

whatever you need you should check out mrcycles.com they have every stock part for any bike.


thanks
buti dont need parts i need ot kow measurments so i can take off my damn front wheel.. i think its like 16MM butio have no clue.. i have to make a gizmo thigie (two nuts on a bold) to take it off liek i used to for my r6...

[RonJ83]

if you have an adjustable wrench that should be able to tell you cause i know my adjustable wrench gives a lil ruler. i looked all over the internet for a 04 service manual and no dice.

[Cakes206]

Though it was something crazy like 24mm...16mm is the pinch bolts I believe.

[RonJ83]

24mm is accually not that big either, my clutch slider was about that big and i would think the front wheel would be bigger.

[SPRHK]

Not real sure without looking it up, you probably need a special tool to remove the front wheel. Motion Pro sells a multi size tool that fits 4 different sizes. It should be an internal hex like an allen bit.

Try spell check, it may help people understand what you're asking.

[Cakes206]

Try spell check, it may help people understand what you're asking.

LMFAO...I gave up about a year ago :roflmao:

Here you go Soda http://www.ronayers.com/catalogs/pu/parts.cfm?topsecid=3&subsecid=28&type=628&secid=105

Or...go to Home Depot and make the tool with a bolt and a couple of nuts...it is 24mm.

[njracer]

thanks
buti dont need parts i need ot kow measurments so i can take off my damn front wheel.. i think its like 16MM butio have no clue.. i have to make a gizmo thigie (two nuts on a bold) to take it off liek i used to for my r6...

Hereyagoman.....lookdownatthebottomofthe postfor abit of newerpics.

http://www.gixxer.com/ubbthreads/showflat.php?Cat=0&Board=2004&Number=1546346&page=0&fpart=all

njracer

[soda7o]

Hereyagoman.....lookdownatthebottomofthe postfor abit of newerpics.

http://www.gixxer.com/ubbthreads/showflat.php?Cat=0&Board=2004&Number=1546346&page=0&fpart=all

njracer

yup thanks cakes and NJ thats exaclty what i was looking for..
so its 24mm outside dimensions of th enut and bold.. meaning its a 16mm nut and bold?

and i will never use no stinking spell check :)

[soda7o]

LMFAO...I gave up about a year ago :roflmao:

Here you go Soda http://www.ronayers.com/catalogs/pu/parts.cfm?topsecid=3&subsecid=28&type=628&secid=105

Or...go to Home Depot and make the tool with a bolt and a couple of nuts...it is 24mm.


i did that whole set up in the pic and it didnt work.. ended up stripping the bolt and nut..

i guess one more trip to home depot for me..

[Cakes206]

Get the tool before ya break somethin :lol:

[soda7o]

Get the tool before ya break somethin :lol:


ok illtry it one more time.. it cost me liek 50 cents for the set up form home depot.. :lol: i am a klepto.. so illtryit one more tim einstead of freakign getting a tool forliek 30 bucks and waiting two weeks for it..

[Cakes206]

ok illtry it one more time.. it cost me liek 50 cents for the set up form home depot.. :lol: i am a klepto.. so illtryit one more tim einstead of freakign getting a tool forliek 30 bucks and waiting two weeks for it..

Any dealer parts dept. should have it. Or I know wcw does...have him mail it to ya.

[DougZ]

I have about 20 of those homemade tools still made up. Who needs one?

Cakes, didn't I send one to you?

[Cakes206]

Cakes, didn't I send one to you?

Yea, for the SV.

[soda7o]

Any dealer parts dept. should have it. Or I know wcw does...have him mail it to ya.


illbe heading up to PA sat so ill just swing by WCW and say hello....
but ill try to make another tool tonight.. i know what my mistake was..

[DougZ]

Yea, for the SV.

Same one for the Gix, isn't it? I use it on my Gix 600, 2001...I think.

[soda7o]

got another set of the bolts and nuts and got the front wheel off
replaced one of the front rotors.. need more locktite to finish the second one

thansk for all your help